OWC Multi-Mount Instrukcja Instalacji

Assembly & Installation ManualMulti-Mount for Mac Pro3.5” to 5.25” Drive Bay Converter Bracket2.5” to 3.5” Drive Bay Converter Bracket

Using a Phillips P0 screwdriver, loosen the PCI Express cover retaining plate and remove it. There is a tab at the top that the metal plate latches in

Remove your PCI Express video card. At the rear of the PCI Express slot, there is a small plastic tab that you need to lift up to unlock the PCI Expre

Take the memory bay and gently move it to the right, towards the back of the computer. You’ll be able to gently shake it and it will pop loose and mov

A view of the processor heatsinks with the cover removed.Some later model Mac Pro systems, especially 8-Core models, have a hidden Phillips screw loca

Take the L shaped PCI card deadplate you removed on page #7. Starting at the top of the fan shroud, work the short end of the bracket into the gap at

Begin by removing the side door on your Mac Pro.Make sure that the locking latch on the back right side of the Mac Pro. Then, remove all 4 of the driv

Remove the cover over the processors by pulling on it. There are mag-nets securing the cover in place.Immediately to the left of the PCI slots, at the

Using your right hand, wiggle, tug, and pull the entire fan assembly out of the computer. It attaches to the logic board via a connector that you don’

Now that you have fully exposed the logic board, look for the 2 SATA ports, circled here. Insert the L shaped SATA cable into the top SATA port on the

Grasp the optical bay with your ngers and pull straight out. The drive carrier may require a bit of shaking to dislodge it from it’s mounts but it wi

1 INTRODUCTION1.1 System Requirements 1.1.1 Computer Requirements 1.1.2 Hard Drive Requirements 1.1.3 Tool Requirements1.2 Package ContentsOWC M

Start routing the SATA cables that you have already attached to the logic board up through the corner of the optical bay, following the existing wire

5.1 Installing either 1 or 2 3.5” Hard Disk DrivesBegin by positioning the bottom 3.5” hard disk drive with the con-nection ports facing away from you

Once you have the right bracket installed, rotate the hard drive and at-tach the left side bracket using the same method as step 1. You also can add a

To install a 2.5” Drive into the OWC Multi-Mount, place the 2.5” drive mechanism on the table in front of you, with the interface connection to the ri

Once you have the 2.5” OWC Multi-mount attached to the 2.5” hard disk drive, you can install up to (2) 2.5” drives onto the 3.5” OWC Multi-Mount brack

Here you see a completed assembly comprised of one set of 3.5” OWC Multi-Mount drive brackets, and two sets of 2.5” OWC Multi-Mounts, all assembled in

This is a completed assembly comprised of one set of 3.5” OWC Multi-Mount drive brackets, and one set of 2.5” OWC Multi-Mount, all assem-bled into one

6.1 Installing the OWC Multi-Mount into a Mac ProAttach the OWC Multi-Mount using the 4 screws that come already in-stalled in the Mac Pro’s optical d

Mac Pro 667MHz Owners; Turn to the end of Chapter 2 and work back-wards to complete reassembly of your Mac Pro.Mac Pro 800MHz Owners: Reinsert the Phi

7.1 TroubleshootingHaving problems installing? Go back and examine the steps and photo-graphs. Most t issues can be traced to missing a step or a scr

OWC Multi-Mount Chapter 6 - Bracket InstallationSet the optical drive assembly into the optical drive bay, there are 2 screws that line up onto a trac

8.1 FAQQ: How do I format my storage solution? A: OWC has detailed instructions online for most popular operating systems, located at: http://eshop.ma

•Read this manual and review Chapter 4: Troubleshooting & Tips.•Try to conrm the problem is with the hard drive. If you have a second computer, m

Copyright ®2010 Other World Computing All Rights Reserved. Other World Computing’s Limited Warranty is not transferable and subject to limitations.Cop

Got tools? If you don’t have the tools necessary to complete this in-stallation, Newer Technology has a fantastic toolkit which includes ev-erything y

OWC Multi-Mount Chapter 1 - Introduction1 INTRODUCTION1.1 System Requirements1.1.1 Computer RequirementsAny 2006 - 2008 Mac Pro system1.1.2 Hard Drive

Begin by removing the side door on your Mac Pro.On the lower right, nd the memory bay.OWC Multi-Mount Chapter 2 - Mac Pro 667MHz Disassembly 2 MAC PR

Remove the 2 memory riser cards, exposing the 2 Phillips screws shown here.Remove the 2 Phillips screws. They are long and extend through the logic bo

At the bottom of the memory bay, there are 2 more Phillips screws. They are a smaller head than the ones inside the memory bay that you just removed.

Make sure that the locking latch on the back right side of the Mac Pro. Then, remove all 4 of the drive bays and set them aside.Look inside the PCI Ex